Yetter 71 Series Planter Manual de usuario

6010 PLANTER UNIT OPERATOR’S MANUAL & PARTS IDENTIFICATION 2565-724_REV_B ● 05/2013 YETTER MANUFA

10 PLANTING UNIT ASSEMBLY HOPPER BOTTOM-BEETS, LOW-RATE SORGHUM OR CUCUMBER 1. Install cutoff (A) in hopper bottom. NOTE: Be certain cuto

11 PLANTING UNIT ASSEMBLY HOPPER BOTTOM-PEANUTS OR EDIBLE BEANS 1. Install peanut cutoff (A) and floor plate (B) on hopper bottom and

12 PLANTING UNIT ASSEMBLY HOPPER BOTTOM-SOYBEANS AND COTTON SEED (ACID, FLAME, ZIP OR MECHANICALLY DELINTED) NOTE: Stirring rod (A) must be remove

13 PLANTING UNIT ASSEMBLY 1. Install lid and hopper on planting units. Pull latch past locating lug and rotate forward when installing hopper.

14 SMV EMBLEM INSTALLATION

15 OPTIONAL LIGHT KIT INSTALLATION 3400-175

16 OPERATING THE PLANTER NOTE: Be sure seed tube (A) is installed in clip (B) as shown at right. Double-Disk Seed Opener

17 OPERATING THE PLANTER DRILLING DISTANCES Four sprockets are shipped with each unit; 11-, 14-, 20- and 22-tooth sprockets. These sprockets will

18 ATTACHMENT ASSEMBLY INSTRUCTIONS PARKING STAND ASSEMBLY

19 OPERATING THE PLANTER LEVELING Drive tractor and planter on level ground. Adjust planter frame to 16 inches (405 mm) above ground.

2 FOREWORD You’ve just joined an exclusive but rapidly growing club. For our part, we want to welcome you to the group and thank you

20 OPERATING THE PLANTER Two holes (B) and (C) in the main chain housing (A) permit finer adjustment. To increase the planting depth

21 OPERATING THE PLANTER CENTERING PRESS WHEEL If press wheel (A) does not track directly behind seed opener (B), loosen round head bolts (C) behin

22 OPERATING THE PLANTER PLANT POPULATION APPROXIMATE PLANT POPULATION PER ACRE CHECKING PLANT POPULATION

23 PREDELIVERY LUBRICATION PREDELIVERY LUBRICATION Note that lubrication intervals are identical to those appearing in the operator’s manual.

24 LUBRICATION ROLLER CHAIN LUBRICATION The most effective roller chain lubrication routine varies, depending on the environmental conditions an

25 STORAGE BEGINNING OF THE SEASON SERVICE Before using the planter after it has been stored, inspect the seed hoppers for cleanliness to be certai

26 PARTS IDENTIFICATION SEED HOPPER ASSEMBLY KEY QTY. PART NO. DESCRIPTION 1. 1 6010-300 LID, HOPPER

27 PARTS IDENTIFICATION PARALLEL ARMS AND TOOLBAR SUPPORTS KEY QTY. PART NO. DESCRIPTION 1. 8 6010-398 BUS

28 PARTS IDENTIFICATION HOPPER DRIVE CASE ASSEMBLY AND DEPTH ADJUSTMENT CAM KEY QTY. PART NO. DESCRIPTION 1. 2 6010-311 7/16” JAM NUT ZYD.

29 PARTS IDENTIFICATION BAFFLE AND ACID DELINTED COTTON, BEANS, REGULAR RATE MAIZE AND CORN KEY QTY. PART NO. DESCRIPTION

3 SAFETY PRECAUTIONS You can make your farm a safer place to live and work if you observe the safety precautions given. Study

30 PARTS IDENTIFICATION SPRING, PLUG AND ANCHOR KEY QTY. PART NO. DESCRIPTION 1. 1 2502-372 ½-13 X 6-1/2” HHC

31 PARTS IDENTIFICATION SEED BOOT, DISK AND BEARING ASSEMBLY KEY QTY. PART NO. DESCRIPTION 18. 2 6010-395 DISK, 12” X .079”

32 PARTS IDENTIFICATION SEED BOOT AND DRIVE KEY QTY. PART NO. DESCRIPTION 1. 2 2533-110 ¼ STRAIGHT SELF-TAP ZERK 2. 1 6010-388 BOLT 3

33 PARTS IDENTIFICATION CORN CUTOFF FOR SEED HOPPER KEY QTY. PART NO. DESCRIPTION 1. 1 6010-328 CAP 2. 1 6010-319 ¼

34 PARTS IDENTIFICATION PRESS WHEEL AND TIRES KEY QTY. PART NO. DESCRIPTION 3. 1 6010-385 TIRE, 4 X 16 CH

35 TROUBLESHOOTING Problem Inaccurate drop Planting more seed in some rows than in others Too many skips. Depth adjusting

36 Our name Is getting known Just a few years ago, Yetter products were sold primarily to the Midwest only. Then we embarked on a pro

4 TABLE OF CONTENTS PAGE FORWARD/WARRANTY……………………………………………………….2 SAFETY INFORMATION……….………………………………………..……..

5 GENERAL INFORMATION To achieve maximum performance, this machine must be assembled as outlined in this instruction manual. The planter operator’s

6 ASSEMBLY INSTRUCTIONS Step 1. Place the toolbar on two assembly stands approximately 28 inches above the floor or ground. FRONT VIEW OF HITCH

7 PARTS IDENTIFICATION 6010-010 – CAT I HITCH KIT

8 PLANTING UNIT ASSEMBLY HOPPER BOTTOM-CORN, SOYBEANS, ACID DELINTED COTTON AND REGULAR-RATE SORGHUM. 1. Install cutoff (A) in hopper bottom

9 PLANTING UNIT ASSEMBLY 7. When planting corn, soybeans, or acid-delinted cotton with the fiber glass hopper, remove cap screws (A) from